ALL RESET

All reset is used when first setting the watch or when there is unusual or erratic operation.

This function can be performed from any mode.

1 - Pull out the crown (d) to the setting position.

2 - Hold down the A,B, and M buttons simultaneously for more than 2 seconds then release them.

All digital segments will light up and a beep will be heard.

1 - Push the M (Mode) button to select the TME (Time) mode.

2 - Press the B button to select the city for which the time is to be set.

3 - Press and hold the B button for 2 seconds or more. 'S.T. (Summertime Abbreviation and ON or OF) flashes. Press the A button to select Summertime ON or OF for that city.

4 - With each press of the B button the segments in the digital display will blink in the order, Summertime, Seconds, Minutes, Hours, 12/24 hour. The segments which are blinking are the ones to be adjusted.

5 - Press the A button to adjust the blinking segment, then press the B button to move to the next segment. If the A button is held down the setting will advance rapidly.

6 - After correcting the time on the digital displays, push button M in to normal position to complete time setting.

The flashing display will automatically return to normal time mode if no button is pressed for 2 minutes.
When using the 12 hour system pay attention to the morning (A) and afternoon (P) indicators.
Summertime mode can be set individually for any city. When set it affects all modes for that city (alarm 1, alarm 2).

1 - Pull out the crown (d) when the second hand reaches '0' (12:00).
2 - Turn the crown in either direction to set hours and minutes.
3 - When the time reference reaches '0' push the crown in.

1 - Push the M button until the mode display (a) shows CAL (calendar).

2 - Press the B button to select the desired city.

3 - Press and hold the the B button for 2 seconds or more, The 'Month' starts flashing. Press the A button to adjust the month ( 1 - 12).

4 - Press button B to change the blinking digits from month to day to year.

5 - Use the A button to change the value of the blinking digits.

6 - When done push the M button to return to normal time display.

Note: The year can be set from 1995 to 2099. The day is automatically set based upon the month, date and year. When the date is set for any one city all other cities are corrected automatically.

Alarm Setting

1 - Press the M button to move to the desired alarm AL-1, or AL-2.

2 - Press the B button to select the city that you want to set the alarm for.

3 - Press and hold the B button for 2 seconds or more. The 'Hour' display will start flashing. Press the A button to adjust the hour.

4 - Press the B button while the 'Hour' is flashing and the 'Minute' display will begin to flash. Press the A button to adjust.

5 - When done press the M button to return to normal timekeeping.

When in alarm mode you can hear the alarm by keeping the A button pressed (Alarm sound monitor function).
When the alarm sounds it can be turned off by pressing any button.

Switching the Alarm ON or OFF.
Press the A button when in alarm mode to change the alarm from ON to OFF. The alarm display will show the word 'OFF' when that alarm is turned off.

Timer Setting

1 - Press the M button to move to the timer mode TMR.

2 - Press the B button to set the desired time in minutes. Keeping the B button pressed will rapidly advance the setting.

4 - Push the M button to return to normal timekeeping.

Using the Timer

1 - Press the M button to move to the timer mode TMR.

2 - Push the A button to start the timer. When the set time has expired the watch will beep.

3 - Push the A button to STOP the timer.

4 - Push the B button to reset the timer back to the set time.

Using the Chronograph

1 - Press the M button to move to the chronograph mode CHR.

2 - Press button A to start the count.

3 - Press button A once again to stop the count.

4 - Press button B to reset the count to '00:00'.

When the count is proceeding after pressing button A pressing button B will display the elapsed time for 10 seconds (SPLIT).